Buscar en Google Scholar
Título: Evaluación numérica de 05 ensayos de muros tipo Pircas al volteo por medio de un programa de análisis numérico
Otros títulos: Numerical evaluation of 05 turn-over pirca type wall tests through a numerical analysis program
Asesor(es): Lipa Cusi, Leonel
Campo OCDE: https://purl.org/pe-repo/ocde/ford#2.01.01; https://purl.org/pe-repo/ocde/ford#2.00.00
Fecha de publicación: 13-nov-2023
Institución: Universidad Peruana de Ciencias Aplicadas (UPC)
Resumen: En el Perú cada vez es más frecuente la autoconstrucción a base de muros de junta seca tipo pirca y así también las noticias sobre accidentes a consecuencia de estas construcciones sin supervisión alguna. Debido a esto, nos centramos en la evaluación numérica de cinco configuraciones distintas de muros tipo pirca sometidas al volteo, a partir de información recopilada de ensayos experimentales en laboratorio. De esta manera, se pretende determinar si es posible representar a través de un modelo numérico, un ensayo real. Para lograr este objetivo se compararon los resultados obtenidos de 05 ensayos experimentales con los de los modelos numéricos realizados. Las dimensiones promedio de los muros ensayados fueron de 4.00m de largo, 0.60m de espesor y 1.45m de alto. Los resultados de los ángulos de colapso totales obtenidos para los modelos numéricos de las cinco configuraciones que son los muros 6, 7, 8, 9 y 10 fueron 21.53°, 19.78°, 20°, 19.72° y 20.21° mientras que para los ensayos experimentales fueron 20°, 22°, 23°, 20° y 20° respectivamente. Entonces, luego de iterar los parámetros de contacto entre los elementos de las pircas, sugieren que es posible representar parcialmente los modos de falla y ángulos de colapso. Finalmente se determinó que para obtener resultados más significativos es necesario modular las pircas a un nivel de detalle mayor en el que se tenga en cuenta la integración e interacción de los elementos más pequeños que conforman las pircas.

In Peru, self-construction based on pirca-type dry joint walls is becoming more frequent and so are the news about accidents as a result of these constructions without any supervision. Due to this, we focus on the numerical evaluation of five different configurations of turn -over pirca-type walls tests, based on information collected from experimental laboratory tests. In this way, the aim is to determine if it is possible to represent a real test through a numerical model. To achieve this objective, the results obtained from 05 experimental tests were compared with those of the numerical models carried out. The average dimensions of the walls tested were 4.00m long, 0.60m thick and 1.45m high. The results of the total collapse angles obtained for the numerical models of the five configurations that are walls 6, 7, 8, 9 and 10 were 21.53°, 19.78°, 20°, 19.72° and 20.21° while for the tests experimental were 20°, 22°, 23°, 20° and 20° respectively. Thereby, after iterating the contact parameters between the elements of the pircas, it suggests that it is possible to partially represent the failure modes and collapse angles. Finally, it is determined that for more significant results it is necessary to modulate the pircas at a higher level of detail in which the integration and interaction of the smallest elements that make up the pircas are considered.
Enlace al repositorio: http://hdl.handle.net/10757/669959
Nota: Posible publicación en revistas indexadas
Disciplina académico-profesional: Ingeniería Civil
Institución que otorga el grado o título: Universidad Peruana de Ciencias Aplicadas (UPC). Facultad de Ingeniería
Grado o título: Ingeniero Civil
Jurado: Sotomayor Cruz, Cristian Daniel; Peña Torres, Pablo Jhoel
Fecha de registro: 24-dic-2023



Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons