Buscar en Google Scholar
Título: Uso de árboles maderables tornillo (Cedrelinga catenaeformis), bolaina (Guazuma crinita) y capirona (Callycophyllum spruceanum) como componentes de un sistema agrosilvopastoril
Asesor(es): Pashanasi Amasifuen, Beto
Campo OCDE: Agricultura; http://purl.org/pe-repo/ocde/ford#4.01.01
Fecha de publicación: 2014
Institución: Universidad Nacional de la Amazonía Peruana
Resumen: This research work was carried out in the field of the Yurimaguas Experimentation and Teaching Center (CEEY) Km 17 of the National University of the Peruvian Amazon - Faculty - Zootechnics, located on the Yurimaguas - Tarapoto highway. The soil is classified as Ultisol, with a pH of 3.8 to 4.2, with low phosphorus content, and high saturation index of aluminum. The objective of this work was to determine the growth of height and diameter of three timber species (screw (Cedrelinga catenaeformis, Bolaina (Guazuma crinita) and Capirona (Callycophyllum spruceanum) as components of an Agrosilvopastoral system in the first seventeen months of established, likewise determine the cost of establishment of these timber species. The experimental procedure began with the preparation of the land through cultural work, then the distribution of the area was carried out applying a statistical design of Completely Randomized Blocks (BCR), with 03 treatments and 03 repetitions. The treatments were T0: screw; T1: screw + capirone and T2: screw + ball. At the beginning of the establishment, the forest components were associated with annual rice (Oryza sativa) and cassava (Manihot sculenta) crops, then a coverage of Centrosema macrocarpum will be established. The best result in growth of height and shaft diameter at seventeen months was observed in T2, with an average height for the screw species 239.79 cm and diameter of 4.54 cm, for a growing ball height 359.01 cm. and diameter of 5.06 cm. Finally, it was concluded that the T2 screw with ball and annual culture obtained better results both in height and shaft diameter growth, differentiating numerically from the other treatments.

El presente trabajo de investigación se llevó a cabo en el terreno del Centro de Experimentación y Enseñanza Yurimaguas (CEEY) Km 17 de la Universidad Nacional de la Amazonia Peruana – Facultad – Zootecnia, ubicado en la carretera Yurimaguas – Tarapoto. El suelo es clasificado como Ultisol, con un pH de 3.8 a 4.2, con bajo contenido de fósforo, y alto índice de saturación de aluminio. El objetivo de este trabajo fue determinar el crecimiento de altura y diámetro de tres especies maderables (tornillo (Cedrelinga catenaeformis, bolaina (Guazuma crimmita) y capirona (Callycophyllum spruceanum) como componentes de un sistema Agrosilvopastoril en los primeros diecisiete meses de establecido, así mismo determinar el costo de establecimiento de estas especies maderables. El procedimiento experimental comenzó con la preparación del terreno mediante labores culturales, luego se realizó la distribución del área aplicando un diseño estadístico de Bloques Completamente Randomizado (BCR), con 03 tratamientos y 03 repeticiones. Los tratamientos fueron T0: tornillo; T1: tornillo + capirona y T2: tornillo + bolaina. Al iniciar el establecimiento los componentes forestales fueron asociados con cultivos anuales de arroz (Oryza sativa) y yuca (Manihot sculenta), luego se establecerá una cobertura de Centrosema macrocarpum. El mejor resultado de crecimiento en altura y diámetro de fuste se observó a los diecisiete meses en el T2, obteniendo como promedio de altura en la especie tornillo de 239.79 cm, con un diámetro de 4.54 cm y en la especie bolaina con promedio de altura correspondiente a 359.01 cm, con un diámetro de 5.06 cm. Finalmente se pudo concluir que el T2 tornillo con bolaina y cultivo anual se obtuvieron mejores resultados tanto en crecimiento de altura y diámetro de fuste, diferenciándose numéricamente de los otros tratamientos.
Disciplina académico-profesional: Zootecnia
Institución que otorga el grado o título: Universidad Nacional de la Amazonía Peruana. Facultad de Zootecnia
Grado o título: Ingeniero(a) Zootecnista
Fecha de registro: 27-ene-2020; 27-ene-2020



Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons