Look-up in Google Scholar
Full metadata record
Ñique Gutierrez, Norberto Damian
Amaya Cuipa, Gulmar Alexander
Rabanal Miñano, Luis Enrique
8/17/2018 14:16
8/17/2018 14:16
2016-01
https://hdl.handle.net/20.500.14414/10594
In this research, the influence of the preheating temperature is evaluated in the range of 100 ° C to 260 ° C on resistance to creep, high tensile strength, percentage elongation of the welded joint to the PASE Root for the FCAW Process and filled by the SAW process and notch toughness Charpy type of cross ZAC to weld steel P460NL1. To this end tensile test specimens according to standard ASME IX were machined. 2013: 190-192; Impact specimens with ASTM E21.02 and for locating notch according to the standard (ISO 9016: 2001). Enabling, cutting, machining and assembling of steel plates P460NL1 was held in the Company GZC Fabrications. The welding was performed following established UN WPS AS ASME Code Section IX-2013. 02 welds in multipass, for FCAW and 05 cords multipass SAW were deposited in the double seal V. control the temperatures start preheating and interpass, it was performed by thermal blankets and digital pyrometer. Subsequently the tests Magnetic Particle justify the acceptance or rejection of the samples for the study. Toughness and tensile specimens were tested at the notch in the Company Sider Peru SA, Chimbote - Ancash in the Laboratory of Physical Testing and Quality Control Ambient Temperature preheat a different course levels. The results showed that increasing does the preheating temperature levels 100 to 260 ° C decreased the yielding stress and maximum tensile strength (UTS) was not significantly affected. The ductility measured by percentage elongation itself increased levels of 220 and 260°C. The notch toughness type Charpy V-notch in the HAZ area para Stuffing With Process did not see any significant variation, this should be the microstructure provided by the process, the specimens were deformed at 45 °C, indicating mayor ductility. (es_PE)
En el presente trabajo de investigación, se evalúa la influencia de la temperatura de precalentamiento en el rango de 100 °C a 260 °C sobre la resistencia a la fluencia, resistencia máxima a la tracción, porcentaje de elongación de la unión soldada para el pase de raíz por el proceso FCAW y relleno por el proceso SAW y la tenacidad a la entalla tipo Charpy de la ZAC transversal al cordón de soldadura del acero P460NL1. Para tal fin se maquinaron probetas para tracción de acuerdo a la norma ASME IX. 2013:190-192; probetas de impacto con norma ASTM E21.02 y para la localización de la muesca de acuerdo a la norma (ISO 9016:2001). La preparación de las planchas de acero P460NL1 se realizó en la empresa GZC Fabricaciones. La soldadura se realizó siguiendo un WPS según el código ASME sección IX-2013. Se depositaron 02 cordones de soldadura, en multipase, por FCAW y 05 cordones de multipase SAW en junta doble V el precalentamiento de inicio y de interpase, se realizó por mantas térmicas y pirómetro digital. Posteriormente el ensayo con partículas magnéticas justificó la aceptación o rechazo de las probetas para el estudio. Se ensayaron probetas a tracción y tenacidad a la entalla en la Empresa Sider Perú SA, Chimbote – Ancash en el laboratorio de Ensayos Físicos y Control de Calidad a temperatura ambiente a diferentes niveles de precalentamiento. Los resultados determinaron que al aumentar la temperatura de precalentamiento en los niveles de 100 a 260°C el esfuerzo de fluencia disminuyo y la resistencia máxima a la tracción no se afectó significativamente. La ductilidad cuantificada por porcentaje de elongación se incrementó en los niveles de 220 y 260°C. La tenacidad a la entalla tipo Charpy con muesca en V en la zona ZAC para el relleno con el proceso SAW no mostro variación significativa, esto se debe a la microestructura provista por el proceso, las probetas se deformaron a 45°C, lo que indicaría ductilidad mayor. (es_PE)
Tesis (es_PE)
spa (es_PE)
Universidad Nacional de Trujillo (es_PE)
Tmat;Tmat
info:eu-repo/semantics/openAccess (es_PE)
http://creativecommons.org/licenses/by-nc-nd/2.5/pe/ (es_PE)
Universidad Nacional de Trujillo (es_PE)
Repositorio institucional - UNITRU (es_PE)
Soldadura (es_PE)
Propiedades a tracción y tenacidad a la entalla transversales a la unión soldada del acero p460nl1 mediante proceso fcaw en el pase de raíz y por saw para acabado a diferentes temperaturas de precalentamiento (es_PE)
info:eu-repo/semantics/bachelorThesis (es_PE)
Universidad Nacional de Trujillo. Facultad de Ingeniería (es_PE)
Ingeniería (es_PE)
Título Profesional (es_PE)
Ingeniero de Materiales (es_PE)
Pública



This item is licensed under a Creative Commons License Creative Commons