Look-up in Google Scholar
Title: Efecto de la temperatura de recocido sobre la resistencia a la tracción, tensión de fluencia, ductilidad, dureza y microestructura en una fundición nodular astm a536
Advisor(s): Purizaga Fernandez, Ismael
Issue Date: Mar-2019
Institution: Universidad Nacional de Trujillo
Abstract: En la presente investigación se estudió el efecto de la temperatura de recocido sobre la resistencia a la tracción, tensión de fluencia, ductilidad, dureza y microestructura de una fundición nodular ASTM A536, por lo cual se utilizó barras de diámetro de 16 mm x 200 mm de longitud, fabricados por la empresa Fundición Laminar SAC – Lima, los cuales fueron recocidos a las temperaturas de 800, 850, 900, 950 y 1000°C por espacio de 20 horas con enfriamiento lento dentro del horno. Las probetas fueron maquinadas para el ensayo de tracción según norma ASTM E-8 y para el ensayo de dureza según norma ASTM E-140. Los resultados experimentales muestran que al incrementar la temperatura de recocido la resistencia a la tracción disminuye desde 443.40 MPa para 800°C hasta 386.70 MPa para 1000°C, la tensión de fluencia disminuye desde 325.00 MPa para 800°C hasta 281.70 MPa para 1000°C y con respecto a la ductilidad, esta aumenta desde 10.30 hasta 17.60% para 900°C y luego disminuye hasta 13.30% a 1000°C. La dureza disminuye desde 166.0 HB para 800°C hasta 123.40 HB para 1000°C debido a la descomposición de la austenita en ferrita, y que para las temperaturas de 800 y 850°C la descomposición es parcial y microestructuralmente consta de ferrita, algo de perlita y nódulos de grafito (Gn), mientras que para las temperaturas de 900, 950 y 1000°C la transformación de la austenita a ferrita es total porque microestructuralmente constan de ferrita y nódulos de grafito (Gn). Los resultados muestran también que la temperatura mínima de transformación total de la austenita a ferrita es 900°C porque a esta temperatura la fundición nodular ASTM A536 se transforma en fundición nodular ferrítica. Se concluye que la temperatura de recocido por 20 horas con enfriamiento lento dentro del horno afecta significativamente a la resistencia a la tracción, tensión de fluencia, ductilidad y dureza en una fundición nodular ASTM A536, según el análisis estadístico con un 95% de confiablidad
Note: In the present investigation, the effect of the annealing temperature on the tensile strength, yield stress, ductility, hardness and microstructure of a nodular cast iron ASTM A536 was studied, therefore, bars with a diameter of 16 mm x 200 mm in length were used, manufactured by the company Fundición Laminar SAC - Lima, which were annealed at temperatures of 800, 850, 900, 950 and 1000°C for 20 hours with slow cooling inside the oven. The specimens were machined for the tensile test according to ASTM E-8 and for the hardness test according to ASTM E-140. The experimental results show that when increasing the annealing temperature the tensile strength decreases from 443.40 MPa for 800°C to 386.70 MPa for 1000°C, the yield stress decreases from 325.00 MPa for 800°C to 281.70 MPa for 1000°C and with respect to ductility, this increases from 10.30 to 17.60% for 900 ° C and then decreases to 13.30% at 1000°C. The hardness decreases from 166.0 HB for 800°C to 123.40 HB for 1000°C due to the decomposition of austenite in ferrite, and that for temperatures of 800 and 850°C the decomposition is partial and microstructurally it consists of ferrite, some perlite and graphite nodules (Gn), while for temperatures of 900, 950 and 1000°C the transformation of austenite to ferrite is total because microstructurally it consists of ferrite and graphite nodules (Gn). The results also show that the minimum temperature of total transformation of austenite to ferrite is 900 ° C because at this temperature the nodular cast iron ASTM A536 is transformed into ferritic nodular cast iron. It is concluded that the annealing temperature for 20 hours with slow cooling inside the furnace significantly affects the tensile strength, yield stress, ductility and hardness in a nodular cast iron ASTM A536, according to the statistical analysis with a 95% reliability.
Discipline: Ingeniería
Grade or title grantor: Universidad Nacional de Trujillo Facultad de Ingeniería
Grade or title: Ingeniero Metalúrgico
Register date: 8-Jul-2019



This item is licensed under a Creative Commons License Creative Commons