Look-up in Google Scholar
Full metadata record
Zavaleta Gutiérrez, Nilthon Emerson
Rodriguez Horna, Aldo Jesus
Roldan Diaz, Frank Jesus
2017-09-27T17:37:57Z
2017-09-27T17:37:57Z
2016-12
https://hdl.handle.net/20.500.14414/8794
This study investigated the effect of time of tempering at a temperature of 700°C on the creep strength of the steel ASTM A335 grade P22. The tempering temperature corresponded to the industrial tempering temperature and the times evaluated were chosen in such a way to accumulate times of 1, 2, 3, 4, 5, y 6 7 hours. Subsequently, the samples were subjected to creep under conditions of 600 ºC and 160 MPa. The results show that the tempering time to 700 ºC, has a very significant impact on its creep strength of the P22 steel. The steel has the highest resistance to creep for 1 hour tempering, with the minimum creep rate of 9.43x10-6 s-1 and a time to rupture in 136.1 hours. This creep strength falls off sharply to the 4 hours of tempering, with a minimum creep rate of 6.37x10-5 s-1 and a time of rupture of 16.7 hours, and retrieved to the 5 hours of tempering with a minimum creep rate of 2.67x10-5 s-1 and a time to rupture in 43.4 hours. The dissolution of precipitated M2C and both microstructural heterogeneity and precipitation between bainite and ferrite phases, during tempering, causes loss of creep resistance of steel P22. Creep rupture occurs by the nucleation, growth and coalescence of cavities, in proeutectoid ferrite corresponding to the regions. The cavities formed were larger in the sample tempering to 4 hours. (es_PE)
Se investigó el efecto del tiempo de revenido a la temperatura de 700°C sobre la resistencia al creep del acero ASTM A335 grado P22. La temperatura de revenido correspondió a la temperatura de revenido industrial y los tiempos evaluados se eligieron de tal manera de acumular tiempos de 1, 2, 3, 4, 5 y 6 horas. Posteriormente, las muestras fueron sometidas a creep bajo condiciones de 600 ºC y 160 MPa. Los resultados muestran que el tiempo de revenido a 700 ºC, tiene un efecto muy importante en su resistencia al creep del P22. El acero presenta la más alta resistencia al creep para 1 hora de revenido, con una velocidad de deformación mínima de 9.43x10-6 s-1 y un tiempo a rotura de 136.1 horas. Esta resistencia al creep cae marcadamente a las 4 horas de revenido, con una velocidad de deformación mínima de 6.37x10-5 s-1 y un tiempo de rotura 16.7 horas, y se recupera a las 5 horas de revenido con una velocidad de deformación mínima de 2.67x10-5 s-1 y un tiempo de rotura de 43.4 horas. La disolución de los precipitados M2C y la heterogeneidad tanto microestructural como de precipitación entre las fases bainita y ferrita, durante el revenido produce la pérdida de la resistencia al creep del acero P22. La rotura por creep ocurre por la nucleación y coalescencia de cavidades, y fluencia del material en regiones correspondientes a la ferrita proeutectoide. Las cavidades formadas fueron de mayor tamaño en la muestra revenida a 4 horas. (es_PE)
Tesis (es_PE)
spa (es_PE)
Universidad Nacional de Trujillo (es_PE)
Tmet 9283;9283
info:eu-repo/semantics/openAccess (es_PE)
http://creativecommons.org/licenses/by-nc-nd/2.5/pe/ (es_PE)
Universidad Nacional de Trujillo (es_PE)
Repositorio institucional - UNITRU (es_PE)
Influencia del tiempo de revenido sobre la resistencia al creep del acero (es_PE)
Influencia del tiempo de revenido a700 °c sobre la resistencia al creep del acero astm a335 grado p22 (es_PE)
info:eu-repo/semantics/bachelorThesis (es_PE)
Universidad Nacional de Trujillo. Facultad de Ingeniería (es_PE)
Ingenieria (es_PE)
Título Profesional (es_PE)
Ingeniero Metalúrgico (es_PE)
Pública



This item is licensed under a Creative Commons License Creative Commons