Look-up in Google Scholar
Title: Influencia del tiempo de recocido sobre la dureza y resistencia al impacto de una fundición gris perlítica en la obtención de una fundición gris ferrítica
Advisor(s): Purizaga Fernandez, Ismael
Issue Date: 31-Jan-2017
Institution: Universidad Nacional de Trujillo
Abstract: En ésta investigación se estudió la influencia del tiempo de recocido sobre la dureza y resistencia al impacto de una fundición gris perlítica en la obtención de una fundición gris ferrítica. Por lo cual se empleó barras cuadradas de 12 mm x 12 mm x 200 mm de longitud suministrado por fundición metalúrgica y servicio afines (FUMETSA), las cuales fueron recocidas a 860°C a los tiempos de 0.5, 1, 2, 5, 10, 15 y 20 horas con enfriamiento lento dentro del horno. Las probetas fueron maquinadas para el ensayo de dureza según norma ASTM E-140 y resistencia al impacto según norma ASTM E23-98. Los resultados experimentales muestran que al incrementar el tiempo de recocido la dureza disminuye desde 213. 10 HB para suministro (0 horas) a 108.10 HB para 20 horas de tratamiento y la resistencia al impacto aumenta desde 9.40 J para suministro hasta 23.60 J para 20 horas. Esto es debido a la descomposición de la austenita en ferrita grafito en forma de hojuelas haciendo que el material sea blando y tenaz. También mostró que los valores obtenidos de resistencia al impacto (J) para todos los niveles de tiempo de recocido son bajos debido a las hojuelas de grafito que se engruesan con el incremento del tiempo de recocido. También se observa que el tiempo de descomposición total de la austenita en ferrita para la obtención de fundición gris ferrítica para esta fundición en las condiciones de estudio fue de 2 horas. Se concluye que el tiempo de maleabilización influye significativamente la dureza y resistencia al impacto según el análisis estadístico con un 95% de confiabilidad.
Note: In this research the influence of the annealing time on the hardness and impact resistance of a gray pearl smelter in the production of a ferritic gray smelter was studied. For that reason, square bars of 12 mm x 12 mm x 200 mm in length supplied by metallurgy and related services (FUMETSA) were used, which were annealed at 860 ° C at the times of 0.5, 1, 2, 5, 10 , 15 and 20 hours with slow cooling inside the oven. The test pieces were machined for the hardness test according to ASTM E-140 and impact strength according to ASTM E23-98. The experimental results show that by increasing the annealing time the hardness decreases from 213. 10 HB for supply (0 hours) to 108.10 HB for 20 hours of treatment and the impact resistance increases from 9.40 J for delivery up to 23.60 J for 20 hours . This is due to the decomposition of the austenite in graphite ferrite in the form of flakes making the material soft and tenacious. It also showed that the obtained values of impact resistance (J) for all annealing time levels are low due to the graphite flakes that increase with the increase of annealing time. It is also observed that the total decomposition time of the austenite in ferrite to obtain ferritic gray smelter for this melt in the study conditions was 2 hours. It is concluded that the malleability time significantly influences the hardness and impact resistance according to the statistical analysis with 95% reliability.
Discipline: Ingeniería
Grade or title grantor: Universidad Nacional de Trujillo. Facultad de Ingeniería
Grade or title: Ingeniero Metalúrgico
Register date: 26-Dec-2017



Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.