Look-up in Google Scholar
Title: Efecto de la temperatura en austenización simple y doble del tratamiento térmico convencional del acero para herramientas AISI D2 sobre la microestructura, dureza y tenacidad
Advisor(s): Ñique Gutierrez, Norberto Damián
Issue Date: Dec-2019
Institution: Universidad Nacional de Trujillo
Abstract: Se estudió el efecto de la temperatura sobre la microestructura, la dureza y tenacidad en la entalla con muesca en U del acero AISI D2 tratado térmicamente en ciclos térmicos correspondientes a Austenización Simple a 850°C, 950°C y 1100°C y Doble Austenización a 850-850°C, 850-950°C, 850-1100°C, 950-850°C, 950-950°C, 950-1100°C, 1100-850°C, 1100-950°C y 1100-1100°C. Se prepararon probetas prismáticas de 0.6 x 0.6 x 5.5 cm que fueron tratadas térmicamente en un Dilatómetro Serie L75 Premium, el control de las temperaturas y las velocidades de enfriamiento del ciclo térmico se realizó mediante el software del dilatómetro. Posteriormente se prepararon las probetas bajo la norma ASTM E- 23 para el ensayo Charpy con muesca en U y donde se midieron la dureza en HV20 bajo la norma ASTM E 92. Bajo la norma ASTM E-93 se prepararon probetas para análisis metalográfico y se determinó el tamaño de grano haciendo uso de microscopia óptica en una primera etapa se determinó una malla representativa de las áreas del grano metálico con el software CorelDRAW x7, posteriormente se determinó las áreas mediante Imagen Pro Plus en función a la escala de la fotomicrografía. Se ajustaron las áreas a un modelo de Lognormal con el software Origin 2018 determinando así la distribución normal de las áreas y el diámetro de grano ASTM, de acuerdo a la norma ASTM E-112. Los resultados determinaron que la temperatura de austenización simple incrementó la dureza significativamente de 222.25 HV20 (850°C) a 302.13 HV20 (1100°C) en doble austenización, los valores se elevaron de 213.5 HV20 (850-850°C) a 405.63 HV20 (1100- 1100°C) determinando un efecto significativo en la temperatura de primera temperatura de austenización. La tenacidad a la entalla KVC (J/cm2) con muesca en U disminuyó a medida que se incrementó la temperatura en austenización simple y doble austenización, para la Simple disminuye de 12.43 J/cm2 a 5.67 J/cm2 y para la doble se tienen los resultados de hasta 14.66 J/cm2 como máximo y de 4.71 J/cm2 como mínimo. Por otro lado se confirmó el incremento de la disolución de carburos aumentando el número de grano ASTM. El tratamiento de doble austenización permitió la disolución de carburos de la aleación durante el primer tratamiento, mientras que la segunda austenización a bajas temperaturas dio un grano más fino de la austenita, aumentando el número ASTM porque los carburos no disueltos proporcionan abundantes sitios de nucleación para la austenita y durante el segundo tratamiento de austenización promueve el tamaño de grano más fino.
Note: The effect of temperature on microstructure, hardness and toughness on the U-noted notch of heat-treated AISI D2 steel was studied in thermal cycles corresponding to Simple Austenization at 850°C, 950°C and 1100°C and Double Austenization at 850-850°C, 850- 950oC, 850-1100°C, 950-850°C, 950-950°C, 950-1100°C, 1100-850°C, 1100-950°C and 1100-1100°C. Prismatic specimens of 0.6 x 0.6 x 5.5 cm were prepared and heat treated on an L75 Series Premium Dilatometer, temperature control and cooling speeds of the thermal cycle was performed using the dilatometer software. The specimens were subsequently prepared under ASTM E-23 for the Charpy U-not test and where the hardness was measured in HV20 under ASTM E 92. Under ASTM E-93, samples were prepared for metallographic analysis and grain size was determined using optical microscopy in a first stage a representative mesh of the metal grain areas was determined with CorelDRAW x7 software, Areas were subsequently determined using Pro Plus Image based on the scale of the photomicrograph. Areas were adjusted to a Log-normal model with Origin 2018 software, thus determining the normal distribution of areas and ASTM grain diameter, in accordance with ASTM E-112. The results determined that the simple austenization temperature increased the hardness significantly from 222.25 HV20 (850°C) to 302.13 HV20 (1100°C) in double austenization, values rose from 213.5 HV20 (850-850ºC) to 405.63 HV20 (1100- 1100°C) determining a significant effect on the first temperature of austenization. The tenacity at the KVC notch (J/cm2) with U notch decreased as the temperature in single and double austenization austenization was increased, for the Simple decreases from 12.43 J/cm2 to 5.67 J/cm2 and for the double the results of up to 14.66 J/cm2 maximum and 4.71 J/cm2 at least. On the other hand, the increase in carbid solution was confirmed by increasing the number of ASTM grain. The double austenization treatment allowed the dissolution of alloy carbides during the first treatment, while the second austenization at low temperatures gave a finer grain of austene, increasing the ASTM number because the carbides did not dissolved sites provide abundant nucleation sites for austeenite and during the second austenization treatment promotes the finest grain size.
Discipline: Ingeniera
Grade or title grantor: Universidad Nacional de Trujillo. Facultad de Ingeniería
Grade or title: Ingeniero de Materiales
Register date:  12



This item is licensed under a Creative Commons License Creative Commons