Look-up in Google Scholar
Full metadata record
Arteaga Caro, Pavel Ovidio
Rosario Dominguez, Max Joe
2018-02-06T17:39:30Z
2018-02-06T17:39:30Z
2017
https://hdl.handle.net/20.500.14414/9696
In the present academic work will be detailed the steps to consider for an efficient choice of pumping units of a pressurized irrigation. It is intended to obtain a manual so that each agricultural engineer can be guided in the choice of the irrigation pump considering as guiding parameters the efficiency of the same and the energy cost along its projected use. This work assumes a correct hydraulic design of the system to be pressurized, so the initial data to be taken into account will be the flows and pressures of the shifts where the pump (s) will work. As a first consideration we will see the importance of the homogeneity of the flows and pressures in a system that intends to use a single type of pump in its filter house. Within the parameters that will determine the pump model is the NPSH which will be a measure to consider according to the position of the water source with respect to the pump; at the same time this value is calculated with the geographical data of the area where the project was executed. Knowing the values of flow rates, pressure and NPSH of the pump to be acquired, we will analyze the performance curves of the different brands that the Peruvian and foreign markets (if the case by decision of the client) offer and that are close to what they are. which we initially have as a working range. When performing this analysis, we will take into account the efficiency and type of pump that we offer to go from there to the analysis of energy cost. Once the pump models have been obtained we will proceed to the analysis of the energy cost of the use of the pumps throughout its operation during the time that is or contemplated the agricultural project. For this analysis, the cost per kW-hour of the H2Olmos project area will be taken into account and the VAN and TIR study of the acquisition of the same will be done to determine the model that will benefit the project of the investment company, both hydraulically and economically. This report is intended as a manual that shows in a simple way the steps that should be considered when choosing the pumps that pressurized irrigation system considering the lowest cost of investment that will ensure an attractive economic return to generate more future that helps economic growth from the country. (es_PE)
En el presente trabajo académico se detallará los pasos a considerar para una eficiente elección de las unidades de bombeo de un riego presurizado. Se pretende obtener un manual para que cada ingeniero agrícola pueda guiarse en la elección de la bomba de riego considerando como parámetros guías a la eficiencia de la misma y al coste energético a lo largo de su uso proyectado. Este trabajo asume un correcto diseño hidráulico del sistema que se desea presurizar, por lo que los datos iniciales que se tendrán en cuenta serán los caudales y presiones de los turnos donde la(s) bomba(s) funcionará(n). Debemos considerar la importancia de la homogeneidad de los caudales y presiones en un sistema que pretende servirse de una sola clase de bomba en su caseta de filtrado. Dentro de los parámetros que nos determinaran el modelo de bomba está el NPSH el cual será una medida a considerar de acuerdo a la posición de la fuente de agua con respecto a la bomba; a la par este valor se calcula con los datos geográficos de la zona donde el proyecto se ejecutara. Conocidos los valores de caudales, presión y NPSH de la bomba que se pretende adquirir pasaremos a analizar las curvas de funcionamiento de las diferentes marcas que el mercado peruano y extranjero (si fuera el caso por decisión del cliente) ofrecen y que se aproximen a lo que inicialmente tenemos como rango de trabajo. Al realizar este análisis tomaremos en cuenta la eficiencia y tipo de bomba que nos ofrecen para de ahí pasar al análisis de costo energético. Una vez obtenidos los modelos de bombas pasaremos al análisis del costo energético del uso de las bombas a lo largo de su operación durante el tiempo que dure o este contemplado el proyecto agrícola. Para este análisis se tomarán en cuenta el costo por kW-hora de la zona del proyecto de H2Olmos y se hará el estudio VAN y TIR de la adquisición de los mismos para determinar el modelo que beneficie hidráulicamente y económicamente el proyecto de la empresa inversionista. Este informe pretende ser un manual que muestre de manera sencilla los pasos que deben considerarse al elegir las bombas que un sistema de riego presurizado requiera considerando el menor costo de inversión que le asegure un retorno económico atractivo para generar más inversión futura que ayude al crecimiento económico del país. (es_PE)
Tesis (es_PE)
spa (es_PE)
Universidad Nacional de Trujillo (es_PE)
TAGC;193
info:eu-repo/semantics/openAccess (es_PE)
http://creativecommons.org/licenses/by-nc-nd/2.5/pe/ (es_PE)
Universidad Nacional de Trujillo (es_PE)
Repositorio institucional - UNITRU (es_PE)
Coste Energético, Presión, ADT, NPSH, Eficiencia, Caudal, Curva. (es_PE)
Estudio de la Selección de Unidades de Bombeo, bajo Los Parametros Eficiencia y Costo de Energia, para El Sistema de Riego por Goteo en 75,26 has de Arandanos (vaccinium myrtillus), en Fundo Olmos (es_PE)
info:eu-repo/semantics/bachelorThesis (es_PE)
Universidad Nacional de Trujillo - Facultad de Ciencias Agropecuarias (es_PE)
Agrícola (es_PE)
Bachiller (es_PE)
INGENIERO AGRÍCOLA (es_PE)
Pública



This item is licensed under a Creative Commons License Creative Commons