Look-up in Google Scholar
Full metadata record
Luján Tupez, Julio
Castillo Valdiviezo, Ancelmo
Sánchez Arias, Juberth Alexander
Cortéz Rojas, Manuel Fernando
2017-11-15T13:32:02Z
2017-11-15T13:32:02Z
2017-11-15T13:32:02Z
2017-11-15T13:32:02Z
2006
https://hdl.handle.net/20.500.14414/9145
In the present work, an investigation was proposed that provided experimental information, which showed the performance of Portland Cement type MS produced with Clinker type V, as a replacement additive of BFS blast furnace slag, in gradual percentages. Through the use of the theoretical information and the steps for the elaboration of Portland cement type MS, based on international standards, such as the ASTM Standard; A comparison was made between the production cost of the same, using BFS blast furnace slag and on the other hand using Clinker type V. This, in order to handle the possibility that the company of "Cementos Pacasmayo SAA" produces its own additive for the elaboration of its Cementos Portland type MS. This research work was carried out, because the company, within about 3 years, will not produce Portland Cement type MS based on BFS Slag, but would be manufacturing the new additive for the total replacement of it, when it is finished in due time; such is the case that the purchase of Escoria BFS is currently being reduced to the steel company Sider Perú de Chimbote. In the different analyzes carried out, the results have been optimal and those required by the ASTM Standard, since the study of cost and production will benefit the company going forward (es_PE)
En el presente trabajo realizado, se planteó una investigación que proporcionaba información experimental, la cual, se demostró el rendimiento del Cemento Portland tipo MS producido con Clinker tipo V, como aditivo reemplazante de la Escoria BFS de alto horno, en porcentajes graduales. Mediante el uso de la información teórica y los pasos para la elaboración del Cemento Portland tipo MS, basados en las normas internacionales, como la ASTM Standard; Se realizó una contrastación entre el costo de producción del mismo, utilizando Escoria BFS de alto horno y por otro lado utilizando Clinker tipo V. Esto, con la finalidad de manejar la posibilidad de que la Empresa de “Cementos Pacasmayo S.A.A.” produzca su propio aditivo para la elaboración de sus Cementos Portland tipo MS. Este trabajo de investigación, se llevó a cabo, debido a que la empresa, dentro de unos 3 años aproximadamente, no elaborará Cemento Portland tipo MS basado en Escoria BFS, sino, se estaría fabricando el nuevo aditivo para el reemplazo total de la misma, cuando ésta se acabe en su debido momento; tal es así, que se está bajando actualmente la compra de Escoria BFS a la empresa siderúrgica Sider Perú de Chimbote. En los diferentes análisis realizados, los resultados han sido óptimos y los requeridos por la norma ASTM Standard, ya que, el estudio de costo y de producción beneficiará a la empresa en adelante (es_PE)
Tesis (es_PE)
spa (es_PE)
Universidad Nacional de Trujillo (es_PE)
info:eu-repo/semantics/openAccess (es_PE)
http://creativecommons.org/licenses/by-nc-nd/2.5/pe/ (es_PE)
Universidad Nacional de Trujillo (es_PE)
Repositorio institucional - UNITRU (es_PE)
Cemento portland, Clinker tipo V, Escoria (es_PE)
Mejoramiento en las propiedades físicas y químicas del cemento portland tipo MS por adición del clinker tipo V, en la sustitución de escoria BFS de alto horno (es_PE)
info:eu-repo/semantics/bachelorThesis (es_PE)
Universidad Nacional de Trujillo.Facultad de Ingeniería Química (es_PE)
Ingeniería Química (es_PE)
Título Profesional (es_PE)
Ingeniero Químico (es_PE)
Pública



This item is licensed under a Creative Commons License Creative Commons