Buscar en Google Scholar
Registro completo de metadatos
Coaquira Rojo, Carlos Alberto (es_PE)
Taza Aquino, Yerson (es_PE)
Quintanilla Mosquera, Iraiz Lucero (es_PE)
Ortiz Zacarias, Jhon Rodrigo (es_PE)
Beraun Espíritu, Manuel Michael (es_PE)
Arzapalo Bello, Ruben (es_PE)
Coaquira Rojo, Carlos Alberto (es_PE)
2024-04-22T01:40:37Z
2024-04-22T01:40:37Z
2024
Taza, Y., Quintanilla, I., Ortiz, J., Beraun, M., Arzapalo, R. y Coaquira, C. (2024). Mechanical and Electronic Design of a Prototype Lower Limb Prosthesis for Transfemoral Amputation. Tesis para optar el título profesional de Ingeniero Mecatrónico, Escuela Académico Profesional de Ingeniería Mecatrónica, Universidad Continental, Huancayo, Perú. (es_PE)
https://hdl.handle.net/20.500.12394/14509
Abstract—In South America, there are few companies that are interested in the creation of prostheses and this, together with the little technological progress, makes patients with transfemoral amputation unable to perform their work. For this reason, the objective of this research is to design a prototype of a lower limb prosthesis for transfemoral amputation that helps the patient's mobility recovery, preventing the wear of the functional knee where an ergonomic design was considered for the patient's comfort. On the other hand, muscular sensors (EMG) were used to detect the intension of the movement, and triaxial accelerometers that capture the movement disturbances in the three axes X, Y, Z. The mechanical design was submitted to the Von Mises stress analysis simulation, these tests were performed in the SolidWorks software and the electronic circuit design was simulated in the Proteus software, where a correct interaction between the different sensors with the actuators of the prosthesis was achieved, in this way, the VDI 2206 methodology was applied. In the results it was possible to simulate the movements of the ankle by the implementation of the Stewart mechanism, also the pieces of the structure were subjected to an analysis where it is shown that efficiently support 68 kg this is related to the height of 165 cm. Finally, it was obtained that the suitable material is aluminum alloy 6061 T-6. (es_PE)
application/pdf (es_PE)
16 páginas (es_PE)
eng (es_PE)
Universidad Continental (es_PE)
https://ieeexplore.ieee.org/document/9965649/
info:eu-repo/semantics/openAccess (es_PE)
https://creativecommons.org/licenses/by/4.0/ (es_PE)
Universidad Continental (es_PE)
Repositorio Institucional - Continental (es_PE)
Diseño (es_PE)
Amputación transfemoral (es_PE)
Análisis de estrés (es_PE)
Mechanical and Electronic Design of a Prototype Lower Limb Prosthesis for Transfemoral Amputation (es_PE)
info:eu-repo/semantics/bachelorThesis (es_PE)
Attribution 4.0 International (CC BY 4.0) (es_PE)
Universidad Continental. Facultad de Ingeniería. (es_PE)
Ingeniería Mecatrónica (es_PE)
Ingeniero Mecatrónico (es_PE)
PE (es_PE)
https://purl.org/pe-repo/ocde/ford#2.00.00 (es_PE)
Pregrado presencial regular (es_PE)
https://purl.org/pe-repo/renati/level#tituloProfesional (es_PE)
200499057
https://orcid.org/0000-0003-1902-3731 (es_PE)
74239368
71689110
70347500
20102191
41058202
20049057
713096 (es_PE)
https://purl.org/pe-repo/renati/type#tesis (es_PE)
Privada societaria
info:eu-repo/semantics/publishedVersion (es_PE)



Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons