Merino, R., (2023). Análisis de la estimación de accidentes en la seguridad vial, mediante la calibración del método predictivo, para la vía Cusco – Puente Cunyac en base al Highway Safety Manual –año 2021 [Universidad Andina del Cusco]. https://hdl.handle.net/20.500.12557/6025
Merino, R., Análisis de la estimación de accidentes en la seguridad vial, mediante la calibración del método predictivo, para la vía Cusco – Puente Cunyac en base al Highway Safety Manual –año 2021 []. PE: Universidad Andina del Cusco; 2023. https://hdl.handle.net/20.500.12557/6025
@mastersthesis{renati/1125586, title = "Análisis de la estimación de accidentes en la seguridad vial, mediante la calibración del método predictivo, para la vía Cusco – Puente Cunyac en base al Highway Safety Manual –año 2021", author = "Merino Yépez, Robert Milton", publisher = "Universidad Andina del Cusco", year = "2023" }
Esta tesis de investigación resulta del análisis de la metodología del HSM para predecir
accidentes en la carretera nacional PE-3S tramo Puente Cunyac - Cusco cuya longitud es de
92Km, donde una vez obtenida la información de accidentabilidad de 15 años, con tipo, causa,
ubicación, fecha de ocurrencia, además de la toma de datos primarios y secundarios para
determinar la geometría vial y las características del entorno, se procedió a investigar al detalle
cada procedimiento específico explicado en la parte C del manual, en lo correspondiente a las
carreteras de una calzada con dos carriles con flujo vehicular en ambos sentidos.
Con la data de accidentabilidad se generaron datos estadísticos descriptivos, identificándose
cuadros donde se muestran la relación de progresivas con mayor accidentabilidad y en
correspondencia con una causa no identificada en los registros de accidentes como son el
incumplimiento del diseño geométrico respecto a tangentes máximas en un sector y mínimas en
otro, estos datos estadísticos nos definieron los tramos con mayor índice de accidentes a estudiar.
En función al requerimiento y recomendación del HSM, se procedió a analizar la data de campo,
para definir los tramos a sectorizar en los 92 Km de estudio, según recomendaciones del HSM, y
son aquellos donde la homogeneidad de la vía cambia por algún detalle, principalmente entre
intersecciones; en este caso se generaron tramos homogenizados por “Orografía”, “por nivel de
accidentabilidad”, y por “tramos con IMD homogéneo”.
La carretera en su tramo Puente Cunyac -Cusco, se homogenizó por orografía en tres tramos de
orografía 1, 3 y 2; luego, los tramos homogenizados por IMDA fueron seis que resulta en
función a los años con los que se cuenta la data, luego en función al análisis estadístico de
accidentes se definió dos sectores generadores de mayor cantidad de accidentes.
Se analiza las variables de ecuación predictiva del HSM: a) consistente en el cálculo de los SPF,
que dependen básicamente del IMDA y longitud del tramo, b) los 12 CMF correspondiente a 12
detalles como son: Ancho de carril, berma, Espiral en curvas, peralte, pendiente de la vía,
numero de accesos, línea central sonora, carril de adelantamiento, carril de giro izquierda, condiciones de los márgenes, iluminación y sistema automático de control de velocidad, y c) el
factor de calibración que se obtiene de la relación de la sumatoria del numero de accidentes
observados con la sumatoria del número de accidentes previstos en el periodo de estudio.
Con esta información se procedió a realizar el procedimiento predictivo consistente en los 18
pasos que muestra el manual HSM; para los tramos diferenciados por IMDA (seis tramos o
sectores y dos intersecciones importantes), se utilizó el Excel propio del HSM versión 3.1
Luego en el tramo más crítico por la alta accidentabilidad ocurrida correspondiente del Km 890
al Km 892 (30 Km), se procedió al análisis según sus detalles geométricos, utilizando el método
manual de análisis considerando los accidentes observados por año de ocurrencia.
Según los cálculos realizados tanto en el Excel procedente del HSM y cálculos manuales del
procedimiento a detalle descrito en esta tesis, se obtuvieron resultados que nos indican factores
de calibración que en su mayoría sobre estiman la accidentabilidad, respecto a los accidentes
observados, obteniéndose valores de Cr de 0.55, 0.25, 1.75, 0.14, 0.24 y 0.48, para los seis
tramos estudiados y verificando el tramo con mayor accidentabilidad. (es_PE)
This research thesis results from the analysis of the HSM methodology to predict accidents on
the PE-3S national highway Puente Cunyac - Cusco section whose length is 92Km, where once
the accident rate information for 15 years has been obtained, with type, cause, location, date of
occurrence, in addition to the collection of primary and secondary data to determine the road
geometry and the characteristics of the environment, each specific procedure explained in part C
of the manual was investigated in detail, as it corresponds to the roads of a road with two lanes
with vehicular flow in both directions.
With the accident rate data, descriptive statistical data was generated, identifying tables showing
the relationship of progressives with greater accident rate and in correspondence with a cause not
identified in the accident records such as non-compliance with the geometric design with respect
to maximum tangents in a sector. and minimal in another, these statistical data defined the
sections with the highest accident rate to study.
Based on the requirement and recommendation of the HSM, the field data was analyzed to
define the sections to be sectored in the 92 km of study, according to HSM recommendations,
and they are those where the homogeneity of the road changes due to some detail. mainly
between intersections; In this case, sections homogenized by “Orography”, “by level of accident
rate”, and “sections with homogeneous IMD” were generated.
The highway in its Puente Cunyac -Cusco section was homogenized by orography into three
sections of orography 1, 3 and 2; Then, the sections homogenized by IMDA were six, which
results based on the years with which the data is available, then based on the statistical analysis
of accidents, two sectors generating the greatest number of accidents were defined.
The HSM predictive equation variables are analyzed: a) consisting of the calculation of the SPF,
which basically depends on the IMDA and length of the section, b) the 12 CMF corresponding to
12 details such as: Lane width, shoulder, Spiral in curves, superelevation, road slope, number of
entrances, audible center line, overtaking lane, left turning lane, shoulder conditions, lighting and automatic speed control system, and c) the calibration factor obtained from the relationship of
the sum of the number of accidents observed with the sum of the number of accidents expected
in the study period.
With this information, the predictive procedure consisting of the 18 steps shown in the HSM
manual was carried out; For the sections differentiated by IMDA (six sections or sectors and two
important intersections), the HSM's own Excel version 3.1 was used.
Then, in the most critical section due to the high accident rate that occurred corresponding to Km
890 to Km 892 (30 km), the analysis was carried out according to its geometric details, using the
manual analysis method considering the accidents observed by year of occurrence.
According to the calculations carried out both in Excel from the HSM and manual calculations of
the detailed procedure described in this thesis, results were obtained that indicate calibration
factors that mostly overestimate the accident rate, with respect to the accidents observed,
obtaining values of Cr of 0.55, 0.25, 1.75, 0.14, 0.24 and 0.48, for the six sections studied and
verifying the section with the highest accident rate. (en_US)
Análisis de la estimación de accidentes en la seguridad vial, mediante la calibración del método predictivo, para la vía Cusco – Puente Cunyac en base al Highway Safety Manual –año 2021 (es_PE)
info:eu-repo/semantics/masterThesis (es_PE)
Universidad Andina del Cusco. Escuela de Pos Grado (es_PE)
Ingeniería Civil con mención en Transportes (es_PE)
Maestro en Ingeniería Civil con mención en Transportes (es_PE)