Look-up in Google Scholar
Title: Adición de Fibras PET en el adobe para aumentar la capacidad resistente a la compresión, reducir: la densidad, el porcentaje de absorción de agua y la conductividad térmica en las viviendas de la zona rural de Ayacucho-Perú
Other Titles: Addition of PET fibers in adobe to increase the compressive strength, reduce: density, water absorption percentage and thermal conductivity in houses in the rural area of Ayacucho-Peru
Advisor(s): Carrera Cabrera, Elsa Carmen
OCDE field: http://purl.org/pe-repo/ocde/ford#2.00.00; https://purl.org/pe-repo/ocde/ford#2.01.01
Issue Date: 1-Feb-2022
Institution: Universidad Peruana de Ciencias Aplicadas (UPC)
Abstract: In the community of Rancha (Ayacucho), there is a high percentage of adobe housing, which is widely used due to its low cost. However, this material presents variations in relation to its resistant capacity and insufficient thermal insulation, the latter being more affected due to the low temperatures of the area. In addition, the density and absorption percentage are not the same for all adobe bricks, since the materials used differ due to the area, climate, etc. The proposed solution is to add PET fibers to the adobe. Therefore, the objective of this work is to determine the effect of PET fibers on the compressive strength, density, absorption percentage and thermal conductivity of adobe. The procedure consists of preparing samples of standard adobe and adobe with PET fibers (2%, 4%, 6%), which will be tested based on the E.080 (adobe) and E.070 (masonry) standards. After performing all the tests, it was determined that the optimum percentage of PET fibers is 6%, since its compressive strength in units increased by 19% and in masonry by 62%. On the other hand, the density was reduced by 16.4%, the absorption percentage by 12% and the thermal conductivity by 35%. For this reason, the proposal contributes to the recycling of PET bottles, to the improvement of the mechanical and physical properties of adobe to extend its life span and to improve thermal comfort inside homes.

En la comunidad de Rancha (Ayacucho), se observa un gran porcentaje de viviendas de adobe, elemento que es altamente usado debido a su bajo costo. Sin embargo, este material presenta variaciones en relación a su capacidad resistente e insuficiente aislamiento térmico, esto último se ve más afectado debido a las bajas temperatura de la zona. Además, la densidad y porcentaje de absorción no son las mismas para todos los adobes, ya que los materiales empleados difieren debido a la zona, clima, etc. La propuesta de solución es añadir fibras PET al adobe. Por ello, este trabajo tiene como objetivo, determinar el efecto de las fibras PET en la resistencia a la compresión, densidad, porcentaje de absorción y conductividad térmica del adobe. El procedimiento consiste en elaborar muestras de adobe patrón y de adobe con fibras PET (2%,4%,6%), las cuales se someterán a ensayos basados en la norma E.080 (adobe) y E.070 (albañilería). Después de realizar todos los ensayos, se determinó que el porcentaje óptimo de fibras PET es el 6%, puesto que su resistencia a la compresión en unidades aumentó en 19% y en muretes un 62%. Por otro lado, la densidad se redujo en 16.4%, el porcentaje de absorción en 12% y la conductividad térmica en 35%. Por esta razón, es que la propuesta contribuye al reciclaje de botellas PET, al progreso de las propiedades mecánicas y físicas del adobe para que su tiempo de vida se prolongue y a mejorar el confort térmico dentro de las viviendas.
Discipline: Ingeniería Civil
Grade or title grantor: Universidad Peruana de Ciencias Aplicadas (UPC). Facultad de ingeniería
Grade or title: Ingeniero Civil
Register date: 25-Feb-2022; 25-Feb-2022



This item is licensed under a Creative Commons License Creative Commons