Look-up in Google Scholar
Title: Análisis comparativo de las propiedades mecánicas de compresión y flexión de un concreto patrón f`c 210kg/cm2 y un concreto reemplazado en porcentajes del 1,2,3 y 4% con Dramix 3D respecto al volumen del agregado fino de la mezcla, elaborado con agregados de las canteras de Vicho y Cunyac.
Advisor(s): Soto Florez, Heiner
Issue Date: 20-Dec-2016
Institution: Universidad Andina del Cusco
Abstract: The main objective of the present research thesis is to make a comparative analysis of a concrete standard f'c 210 kg / cm2 and a concrete added with fibers of steel Dramix 3D, in the resistance of the concrete both to compression and flexion. The concretes were made with portland cement IP, fine aggregate of Cunyac quarries (75%) and Vicho conifer (25%), aggregate of 3/4 of the quarry of Vicho, as these were the selected aggregates that complied with The characteristics required by ASTM C 31, Dramix 3D steel fibers in percentages of 1, 2, 3 and 4% with respect to the volume of the fine aggregate of the mixture and plasticizing additive Sika HE-98, the concrete was designed with the method ACI. A total of 90 cylindrical specimens (10x20cm Briquettes) were used as standard ASTM C 31 and 90 prisms (beams), which were subjected to tests of resistance to compression and flexion with the inclusion of steel fiber in dosages of 1, 2, 3 and 4% in relation to the volume of the fine aggregate of the mixture, amounts considered reasonable for the investigation, based on the data sheets of the suppliers of this material. In the same way, the influence of these steel fibers on the concrete consistency, studied through the Abrams cone, was considered. The results obtained with the inclusion of 2% Dramix 3D steel fibers showed a better compression behavior for 28 days of curing and the inclusion of 3% Dramix 3D steel fibers showed a better flexural behavior for 28 days.

La presente tesis de investigación tiene como objetivo principal hacer un análisis comparativo de un concreto patrón f’c 210 kg/cm2 y un concreto adicionado con fibras de acero Dramix 3D, en la resistencia del concreto tanto a compresión y flexión. Los concretos fueron elaborados con cemento Portland IP, agregado fino de las canteras de Cunyac (75%) y confitillo de Vicho (25%), agregado grueso de ¾’’ de la cantera de Vicho, pues estos fueron los agregados escogidos que cumplieron con las características exigidas por las Normas Técnicas Peruanas, fibras de acero Dramix 3D en porcentajes de 1, 2, 3 y 4% respecto al volumen del agregado fino de la mezcla y aditivo plastificante Sika HE-98, el concreto fue diseñado con el método ACI (American Concrete Institute). Se realizaron 90 probetas cilíndricas y 90 testigos prismáticos de acuerdo a la Norma ASTM C 31/C 31M – 03a (American Society of Testing Materials), las cuales fueron sometidas a ensayos de resistencia a compresión y flexión con la inclusión de la fibra de acero en dosificaciones de 1, 2, 3 y 4% respecto al volumen del agregado fino de la mezcla, cantidades que se consideraron razonables para la investigación, basados en fichas técnicas de los proveedores de este material. De la misma manera se consideró la influencia de estas fibras de acero en la consistencia de concreto, estudiada a través del Cono de Abrams. Los resultados obtenidos con la inclusión de fibras de acero Dramix 3D al 2%, presentaron un mejor comportamiento a compresión para 28 días de curado, y la inclusión de fibras de acero Dramix 3D al 3%, presentaron un mejor comportamiento a flexión para 28 días. En conclusión, el reemplazo en 2% y 3% con fibras de acero Dramix 3D respecto al volumen del agregado fino de la mezcla, dan como resultado un mejor comportamiento a compresión y flexión en el concreto.
Discipline: Ingeniería Civil
Grade or title grantor: Universidad Andina del Cusco. Facultad de Ingeniería y Arquitectura
Grade or title: Ingeniero Civil
Register date: 17-May-2017; 17-May-2017



This item is licensed under a Creative Commons License Creative Commons