Look-up in Google Scholar
Title: Propuesta de concreto fluido con agregados reciclados para la optimización de acabados superficiales en estructuras verticales de concreto armado en la ciudad de Lima
Other Titles: Proposal for fluid concrete with recycled aggregates for the surface in vertical reinforced concrete structures in the city of Lima
Advisor(s): Sotomayor Cruz, Cristian Daniel
OCDE field: https://purl.org/pe-repo/ocde/ford#2.01.01; https://purl.org/pe-repo/ocde/ford#2.00.00
Issue Date: 18-Oct-2023
Institution: Universidad Peruana de Ciencias Aplicadas (UPC)
Abstract: En la presente investigación, se realiza el análisis del comportamiento del concreto fluido incorporando agregados reciclados, con la finalidad de conocer su comportamiento en estado fresco, características mecánicas y acabado superficial. Se analizaron 13 muestras a una resistencia de 280 kg/cm2. Las mezclas fueron divididas en tres grupos, las mezclas M1, M2, M3, M4 y M5 tienen incorporado agregado fino reciclado (AFR), las mezclas M6, M7, M8, y M9 tienen agregado grueso reciclado (AGR), todas con relación a/c de 0.48, las mezclas M10, M11, M12 Y M13 tienen incorporado agregado fino y grueso reciclado a la vez (AR) con una relación a/c de 0.45, en los 3 grupos se incorporó 20, 25, 30 y 35% de agregado reciclado respectivamente. En los resultados de revenimiento las mezclas con 20% de incorporación lograron mejores resultados logrando hasta 9 ¾”, por el contrario, las que tienen reemplazo del 35% lograron como máximo 8 ½”. Respecto a la resistencia mecánicas, todas las mezclas lograron una resistencia mayor a la esperada teniendo una resistencia máxima de 525 kg/cm2 para la mezcla M13. Sin embargo, esta última y la mezcla M10 fueron las que lograron menor resistencia a la flexión de hasta un 7% con respecto a la compresión. Así mismo, la mezcla M6 logro una resistencia a la flexión de 49.8 kg/cm2 que representa el 10% de su resistencia a la compresión. Por último, se analizó el acabado de las muestra mediante el método QSI (Quality Surface Index) donde se hace un análisis visual de los poros presentes en las muestras, y para este ensayo solo se analizaron las mezclas M1, M4, M6 Y M11 ya que las demás mezclas presentaron segregación al momento de realizarlas y solo es posible medir poros de hasta 10 mm de diámetro, el resultado de este análisis fue que la mezcla M6 el cual tiene una incorporación de 20% de (AGR) posee menor porcentaje de poros 1% del área estudiada, en comparación de la mezcla patrón que llego hasta 1.23% de poros del área estudiada.

In the present investigation, the behavior of flowable concrete composed of recycled aggregates was analyzed in order to determine its behavior in the fresh state, mechanical characteristics and surface finish. Thirteen samples were analyzed at a strength of 280 kg/cm2. The mixes were divided into three groups, mixes M1, M2, M3, M4 and M5 have incorporated recycled fine aggregate (RFA), mixes M6, M7, M8, and M9 have recycled coarse aggregate (RCA), all with a w/c ratio of 0. 48, mixes M10, M11, M12 and M13 have both fine and coarse recycled aggregate (RA) with a w/c ratio of 0.45, in the 3 groups 20, 25, 30 and 35% of recycled aggregate were incorporated, respectively. In the slump results, the mixes with 20% incorporation achieved better results achieving up to 9 ¾", on the contrary, those with 35% replacement achieved a maximum of 8 ½". Regarding mechanical strength, all the mixes achieved a higher strength than expected, with a maximum strength of 525 kg/cm2 for mix M13. However, the latter and the M10 mix were the ones that achieved the lowest flexural strength of up to 7% with respect to compression. Likewise, mix M6 achieved a flexural strength of 49.8 kg/cm2, which represents 10% of its compressive strength. Finally, the finish of the samples was analyzed using the QSI (Quality Surface Index) method, where a visual analysis is made of the pores present in the samples, and for this test only mixtures M1, M4, M6 and M11 because the other mixtures showed segregation at the time of testing and it is only possible to measure pores up to 10 mm in diameter, the result of this analysis was that the mixture M6 which has an incorporation of 20% of (AGR) has a lower percentage of pores 1% of the studied area, compared to the standard mixture that reached up to 1. 23% of pores of the studied area.
Note: ODS 9: Industria, Innovación e Infraestructura; ODS 10: Reducción de las Desigualdades; ODS 3: Salud y Bienestar
Discipline: Ingeniería Civil
Grade or title grantor: Universidad Peruana de Ciencias Aplicadas (UPC). Facultad de Ingeniería
Grade or title: Ingeniero Civil
Juror: Ulloa Román, Karem; De La Torre Salazar, Jorge; Rodriguez Dionisio, Sandra
Register date: 27-Feb-2024; 27-Feb-2024



This item is licensed under a Creative Commons License Creative Commons